Questions tagged [error]
An error is the unwanted operation of an electrical / electronic component or system resulting from malfunctions. Use this tag if you have something that doesn't work as it should, or doesn't work at all.
366 questions
1 vote
2 answers
120 views
AM modulation in Multisim doesn't work
I already asked a question about this circuit. Unfortunately, I still haven't been able to get AM modulation working with it. Although other circuits I've been shown work. I still want to find the ...
0 votes
1 answer
42 views
Singular matrix: check node error
What is the problem in my circuit? I tried changing the voltages but its no use. I made the same circuit that was working but it’s not working now. What is wrong with it? I’d be grateful for your help....
- 13
0 votes
1 answer
102 views
AND gate giving error, but shouldn't?
I'm new to logisim evolution and really logic circuits in general. Why does the AND gate at the end give an error? When switch 1 is off it doesn't give an error. When the controlled buffers are ...
- 11
0 votes
1 answer
105 views
Deviation of Time Constant Measurements for Charging and Discharging of Modified RL Circuit
I am tasked with experimentally determining \$\tau\$ for the charge and discharge curves of the modified RL circuit below: where \$R_1 = 560\Omega, R_3\$ (which I prefer to denote \$R_2\$) \$= 200 \...
- 334
1 vote
5 answers
1k views
Markings on a ceramic capacitor cannot be correct
I have a dull green looks exactly like a ceramic standard disk capacitor as usual but with marking 104Z. From what I understand, it can only mean 100,000 picofarads equal to 0.1 microfarad, but the ...
- 261
2 votes
1 answer
131 views
What's the method to solve problems with error handling and restrictions in control systems?
I have the following system that represents a motor turning, all the parameters are strictly positive The first part asks us to find the value of \$K_f \$ that given a constand input of 1 volt the ...
- 405
1 vote
1 answer
84 views
PSpice error floating net
With simple circuit, I’m facing error of floating node in PSpice. Please guide me where I’m going wrong. I tried moving the components and clearing the cache also. Still same error.
- 11
0 votes
1 answer
81 views
STM32L4S5 write data to 2MB flash memory (STM32CubeIDE)
I am trying to write to the flash memory of the STM32L4S5QIIX microcontroller on the EVAL-ADIN1110EBZ development board. I have also tried similar code on an STM32L4S5VITX microcontroller on a custom ...
- 21
1 vote
0 answers
70 views
Error amplifier compensation for voltage-mode flyback converter
I need help understanding how to compensate for the error amplifier in my circuit. My system parameters are as follows: V(In) 4 – 8 V V(Out) 250 V R(Load) 820 kΩ f(SW) 41.5 kHz Compensated ...
- 381
0 votes
2 answers
402 views
Every possible error handlers in stm32
After releasing a firmware update for my custom device, I started noticing that some units were failing to operate correctly. I discovered that writing to the flash memory while the system voltage is ...
- 3
0 votes
0 answers
173 views
How to do a Monte Carlo simulation in LTSPice?
I am trying to do a Monte Carlo simulation of a circuit and its fluctuations from ideal under parameter tolerances. I'm trying to do this in LTSpice making use of component values {mc("Param ...
- 79
1 vote
2 answers
54 views
How'd a certain error percentage (let's say 2%) at a IC at the beginning would translate down a chain of ICs with certain Gains?
As the title says, I would like to know how a 2% error at IC#1 would translate down the chain of ICs (IC#2 gain is 10, IC#3 gain is 5) for the following diagram- Your insights are much appreciated.
- 197
8 votes
5 answers
3k views
Why Is This Faulty H-Bridge Motor Driver Circuit So Popular Despite Its Design Flaws?
I recently built an H-bridge motor driver circuit based on two different configurations I found on the internet First circuit: link of website from where i get this schematic: https://arduinodiy....
- 99
-1 votes
1 answer
155 views
KiCad Pin Assignments
I am creating my own Numpad while loosely following Robert Ferenacs guide on Youtube. He did everything in EasyEDA whereas I wanted to use KiCad. I honestly do not know what I am doing. After ...
2 votes
1 answer
112 views
Trying to replicate a full-wave rectifier circuit in ngspice, but I'm running into an issue where the output isn't behaving as expected
I am in 12th grade, and I have just started learning ngspice. I was experimenting with a part of a circuit that works as a full-wave rectifier, which I found online. I was trying to apply it and ...
- 21