Skip to main content
Electrical Engineering

Questions tagged [stepper-driver]

Ask Question

The tag has no summary.

262 questions
Newest Active Bountied Unanswered
0 votes
3 answers
76 views

I recently bought 3 NEMA 17 stepper motors from pihut.com for a project, and got some A4988 drivers from a company called AZDelivery on amazon.co.uk. Was trying to set up the stepper motors with a ...
JoelTech43's user avatar
  • 11
1 vote
2 answers
231 views

This might have been asked one way or another different times, but I found contradicting answers everywhere, not only here but in online forums as well. Plus, I have a few thoughts that I have not ...
popeye's user avatar
  • 113
1 vote
2 answers
111 views

I have bipolar stepper motor of following specs: 12 V, 0.5 A, 0.43 Nm, 24 Ω, 36 mH. Back-EMF value is 0.0637 Vrms/RPM, measured by spinning it with power tool and measuring open coil voltage on scope: ...
Milek7's user avatar
  • 13
6 votes
3 answers
592 views

I am currently designing a stepper motor driver and have oriented my design on the eval board from the tmc5160. I need lots of vias to provide low inductive paths, as well as stitching for reducing ...
Marvin W's user avatar
  • 85
0 votes
0 answers
41 views

I apologize in advance I'm not the most electrically savvy person. I'm attempting to drive this DRV8231 H-Bridge to drive a stepper motor / peristaltic pump. It hasn't been working well unfortunately. ...
Nick's user avatar
  • 1
1 vote
0 answers
200 views

I have a problem with TMC2209 (Twotrees and MKS v2.0 kit) I have tried at least 5 of it and 4 is burn like image below, I used 17hs4023 stepper motor with 24VDC supply and make sure the current ...
Wahyu Dwi's user avatar
  • 57
0 votes
0 answers
101 views

Attached is my attempt at a circuit "schematic" of a battery powered ESP32 (Seeed Studio XAIO ESP32 RA4M1) which controls 2 mini stepper motors driven by Pololu DV8834 powered from the same ...
loddie's user avatar
  • 31
2 votes
1 answer
397 views

I am using the DM860T stepper motor driver to drive this NEMA 34 stepper motor, and I just want to use a braking resistor to absorb the voltage spike in the event an emergency stop button is pressed ...
Nicolas Montoya's user avatar
  • 173
1 vote
1 answer
94 views

I'm an electrical noob, stepper noob, Arduino intermediate. I cannot interpret online circuit diagrams well enough to figure this out. A Vexta PK243-01AA stepper has six wires. I've identified the ...
Tom's user avatar
  • 21
1 vote
1 answer
104 views

I have a HG7881 H-Bridge 4CH DC - 2CH Stepper Motor Driver Board. For my project, I need to control 5 motors: four 12V DC motors and one 3-6V water pump. I only need to turn the water pump on and off ...
Yax Patel's user avatar
  • 11
0 votes
3 answers
299 views

Here's an excerpt from a 17HF24-1805S datasheet. As I understand it, given the step angle and its accuracy, each step can range from 0.684 to 0.756 degrees. However, will the full rotation angle range ...
beardeadclown's user avatar
  • 267
0 votes
1 answer
111 views

I am looking at the schematics for Makerbase TMC2226 stepper driver board: The schematic shows 1/8W 0.11 ohm current sense resistors. The datasheet for TMC2226 IC says: 8 Selecting Sense Resistors .....
Alan E's user avatar
  • 101
0 votes
2 answers
112 views

I'm totally new in PCB design, especially design with SMD components. Please help me understand what I'm thinking wrong. I'm thinking about placing 3 TMC2226 Silent stepper motor drivers on the same ...
dboodbc's user avatar
  • 1
2 votes
1 answer
226 views

Im using a4988 and are constructing a small pcb carrier for multiple a4988. I have a question on how to connect ms1, ms2, ms3. Do I need pulldown resistors after my DIP switch? Is it necessary? When I ...
acroscene's user avatar
  • 213
0 votes
1 answer
219 views

A year ago, I installed a 10kW hybrid solar inverter for my house. However, due to insufficient sunlight, the solar panels have not been very effective for me. To address this issue, I am planning to ...
SWINGtech's user avatar
  • 1

15 30 50 per page
1
2 3 4 5
…
18